How to use small ultrasonic cleaning machine to remove oil and wax

一、把清洗籃正確的安裝在清洗槽內，一搬是用掛勾掛在清洗槽的兩邊，因?yàn)樾⌒统暡ㄇ逑礄C(jī)的換能器裝在清洗槽底部，如果不用清洗籃的話，清洗物體的重量全部壓在底部，會嚴重降低超聲波清洗機的清洗效果與效率。

1、 First, install the cleaning basket correctly in the cleaning tank. First, hang it on both sides of the cleaning tank with hooks, because the transducer of the small ultrasonic cleaning machine is installed at the bottom of the cleaning tank. If the cleaning basket is not used, the weight of the cleaning object will be pressed at the bottom, which will seriously reduce the cleaning effect and efficiency of the ultrasonic cleaning machine.

二、把清洗物體放在清洗籃內物體不宜太密集，數量合適即可，否則會影響效果，然后往清洗槽內添加清水浸沒清洗物體即可，然后再添加一定比例的除油或者除臘的清洗濟。

2、 Put the cleaning objects in the cleaning basket. The objects should not be too dense, and the quantity should be appropriate, otherwise the effect will be affected. Then add clean water to the cleaning tank to immerse the cleaning objects, and then add a certain proportion of oil or wax removal cleaning oil.

三、按照說明書要求連接電源，檢查指示燈是否正常亮起，如果一切正常，打開超聲控制開關，或旋鈕（具體看是機械控制，還是數碼控制） 調好清洗時間一般除油或者除臘15-20分鐘即可（一次清洗把時間延到30分鐘，因?yàn)檫@時水溫還沒有達到60-70度的工作要求），這時會看到清洗槽里面的液體會有很明顯的，水紋，或者說無數的汽泡，把手伸進去會有明顯的麻麻的感覺。這說明超聲波清洗機已經在開始工作了。

3、 Connect the power supply according to the requirements of the manual and check whether the indicator light is on normally. If everything is normal, turn on the ultrasonic control switch or the knob (see whether it is mechanical control or digital control) and adjust the cleaning time. Generally, the oil or wax can be removed for 15-20 minutes (the time of one-time cleaning is extended to 30 minutes, because the water temperature has not reached the working requirements of 60-70 degrees), At this time, you will see that the liquid in the cleaning tank will have obvious water marks, or countless bubbles, and you will feel numb when you put your hand in it. This shows that the ultrasonic cleaning machine has begun to work.

四、安照說明書要求，把清洗溫度調節到，60--70度即可。 如果覺得燥音太大的話可以把降音蓋蓋上，時間到之后把清洗物體拿起來查看是否已達到清洗要求。如果超聲波清洗機沒問題，或者你清洗的物體沒有特殊要求的話基本上都可以達到你的要求的。

4、 According to the requirements of the installation manual, adjust the cleaning temperature to 60-70 degrees. If you feel that the dry sound is too loud, you can cover the sound reduction cover and pick up the cleaning object after the time is up to check whether the cleaning requirements have been met. If the ultrasonic cleaning machine is OK, or the object you clean has no special requirements, it can basically meet your requirements.

本文的精彩內容由超聲波清洗機價格提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://www.nyvod.cn我們有專門的客服為您解答問題

The wonderful contents of this article are provided by the price and knowledge of ultrasonic cleaning machine. There are many wonderful contents on this website. You can click to enter more contents: http://www.nyvod.cn We have special customer service to answer your questions