服務熱線電話
400-6188-756
標準單槽式超聲波清洗機的使用注意事項
來源:http://www.nyvod.cn/ 時間: 2023-01-05 瀏覽次數: 0
1.超聲波清洗槽無清洗液時 ,絕對不能啟動超聲 ,否則易導致損壞換能器 及超聲波發生器。
1. When there is no cleaning solution in the ultrasonic cleaning tank, the ultrasonic must not be started, otherwise the transducer and ultrasonic generator may be damaged.
2.加熱槽內無清洗液或從槽體內底部測量高度低于250mm ,絕對禁止加熱 , 否則會損壞加熱板。
2. If there is no cleaning solution in the heating tank or the height measured from the bottom of the tank is less than 250mm, heating is absolutely prohibited, otherwise the heating plate will be damaged.
3.不能將物件直接放入超聲波清洗槽底部清洗 ,否則影響超聲清洗效果及磨 損缸底。
3. Do not put objects directly into the bottom of the ultrasonic cleaning tank for cleaning, otherwise the ultrasonic cleaning effect will be affected and the cylinder bottom will be worn.
4.清洗工件如掉入缸底,應及時取出,否則會磨損缸底。
4. If the cleaning workpiece falls into the cylinder bottom, take it out in time, otherwise the cylinder bottom will be worn.
5.避免強力撞擊超聲波清洗槽槽底或振子粘接面,以免損壞換能器。
5. Avoid strong impact on the bottom of the ultrasonic cleaning tank or the bonding surface of the vibrator to avoid damaging the transducer.
6.不可使液體濺濕換能器及超聲波發生器,以免使換能器及線路板受潮短路。
6. Do not wet the transducer and ultrasonic generator with liquid to prevent the transducer and circuit board from being damped and short circuited.
7.使用一定時期,應注意清洗劑量,及時加入清洗液 ,以保證機器正常工作。
7. During a certain period of use, pay attention to the cleaning dosage and add the cleaning solution in time to ensure the normal operation of the machine.

8.槽內沉積物過多時,會使超聲波輸出功率受阻衰減,此時應放液過濾,并清理內槽后,重新放入清洗液繼續工作。
8. If there is too much sediment in the tank, the ultrasonic output power will be blocked and attenuated. At this time, the liquid should be drained for filtration. After the inner tank is cleaned, the cleaning solution should be put in again to continue working.
9.舊液換新時,應在關機狀態及常溫下進行,高溫換液會導致槽體變形,變色。
9. The old liquid shall be replaced with a new one under the shutdown state and normal temperature. High temperature liquid replacement will lead to tank deformation and discoloration.
10.切不可使用可燃性溶劑作清洗劑。
10. Never use flammable solvent as cleaning agent.
1.機器應避免在陽光直接照射下使用或高溫環境下工作。
1. The machine shall not be used under direct sunlight or under high temperature.
12.超聲波發生器應保持通風良好,避免在強酸強堿或惡劣環境下工作。
12. The ultrasonic generator shall be well ventilated to avoid working in strong acid and alkali or harsh environment.
不同廠家的超聲波清洗機價格也是有差別的,我們以優異的性價比著稱于超聲波清洗領域。超聲波清洗機價格高低與清洗質量優劣息息相關,這是我們保證設備品質的同
The prices of ultrasonic cleaners from different manufacturers are also different. We are known for our excellent performance price ratio in the field of ultrasonic cleaning. The price of ultrasonic cleaning machine is closely related to the quality of cleaning, which is the same as the quality of our equipment
1. When there is no cleaning solution in the ultrasonic cleaning tank, the ultrasonic must not be started, otherwise the transducer and ultrasonic generator may be damaged.
2.加熱槽內無清洗液或從槽體內底部測量高度低于250mm ,絕對禁止加熱 , 否則會損壞加熱板。
2. If there is no cleaning solution in the heating tank or the height measured from the bottom of the tank is less than 250mm, heating is absolutely prohibited, otherwise the heating plate will be damaged.
3.不能將物件直接放入超聲波清洗槽底部清洗 ,否則影響超聲清洗效果及磨 損缸底。
3. Do not put objects directly into the bottom of the ultrasonic cleaning tank for cleaning, otherwise the ultrasonic cleaning effect will be affected and the cylinder bottom will be worn.
4.清洗工件如掉入缸底,應及時取出,否則會磨損缸底。
4. If the cleaning workpiece falls into the cylinder bottom, take it out in time, otherwise the cylinder bottom will be worn.
5.避免強力撞擊超聲波清洗槽槽底或振子粘接面,以免損壞換能器。
5. Avoid strong impact on the bottom of the ultrasonic cleaning tank or the bonding surface of the vibrator to avoid damaging the transducer.
6.不可使液體濺濕換能器及超聲波發生器,以免使換能器及線路板受潮短路。
6. Do not wet the transducer and ultrasonic generator with liquid to prevent the transducer and circuit board from being damped and short circuited.
7.使用一定時期,應注意清洗劑量,及時加入清洗液 ,以保證機器正常工作。
7. During a certain period of use, pay attention to the cleaning dosage and add the cleaning solution in time to ensure the normal operation of the machine.

8.槽內沉積物過多時,會使超聲波輸出功率受阻衰減,此時應放液過濾,并清理內槽后,重新放入清洗液繼續工作。
8. If there is too much sediment in the tank, the ultrasonic output power will be blocked and attenuated. At this time, the liquid should be drained for filtration. After the inner tank is cleaned, the cleaning solution should be put in again to continue working.
9.舊液換新時,應在關機狀態及常溫下進行,高溫換液會導致槽體變形,變色。
9. The old liquid shall be replaced with a new one under the shutdown state and normal temperature. High temperature liquid replacement will lead to tank deformation and discoloration.
10.切不可使用可燃性溶劑作清洗劑。
10. Never use flammable solvent as cleaning agent.
1.機器應避免在陽光直接照射下使用或高溫環境下工作。
1. The machine shall not be used under direct sunlight or under high temperature.
12.超聲波發生器應保持通風良好,避免在強酸強堿或惡劣環境下工作。
12. The ultrasonic generator shall be well ventilated to avoid working in strong acid and alkali or harsh environment.
不同廠家的超聲波清洗機價格也是有差別的,我們以優異的性價比著稱于超聲波清洗領域。超聲波清洗機價格高低與清洗質量優劣息息相關,這是我們保證設備品質的同
The prices of ultrasonic cleaners from different manufacturers are also different. We are known for our excellent performance price ratio in the field of ultrasonic cleaning. The price of ultrasonic cleaning machine is closely related to the quality of cleaning, which is the same as the quality of our equipment
上一篇:高壓水去毛刺清洗機用到的技術有哪些?
下一篇:碳氫清洗機軸承清洗的利器
相關文章
-
別誤解工業清洗!通過式清洗機:專啃工業重油污,不是設備無用是認知不足 2026-03-27
-
五金汽配老板必看!單工位旋轉噴淋清洗機,效率翻3倍,工人減負好留人 2026-03-26
-
碳氫清洗機:精密件無殘污,全自動升降拋動,環保耐用還省本 2026-03-26
-
單工位旋轉噴淋清洗機:定制級厚材做工,重污凈洗不晃不變形,耐用十年 2026-03-25
-
碳氫清洗機:孔隙精密件凈洗神器,油污速溶無殘留,告別水基清洗短板 2026-03-25
-
超聲波清洗越洗越臟?別省換水成本,水質才是潔凈核心 2026-03-24
-
機械零件清洗卡脖子?通過式噴淋清洗機,縫隙油污全剝離,產能翻倍 2026-03-24
-
超聲波清洗機不是萬能款!分清品類、選對用法,才是真高效 2026-03-23
-
發動機大修必看:超聲波清洗機,洗出原廠潔凈,拒絕殘留返工 2026-03-23
-
全自動高壓去毛刺清洗機:機油泵體專屬,一鍵啟動實現全流程自動清洗 2026-03-13

新聞中心




常見問題







魯公網安備37011202000628號